RV Parking Air-Conditioner Battery Procurement — Runtime, Peak Load and Acceptance
A rooftop or parking air conditioner is often the largest electrical load an RV, motorhome, campervan or caravan will ask of its house battery (also called a leisure battery or living-area battery). Sizing that battery from a weekend lighting-and-fridge budget, then hoping the air conditioner will “just run,” is a different procurement job from the general RV selection and system-design pages already on this site.
This page is a buying, RFQ and acceptance checklist for that job. LJY Energy supplies complete LiFePO4 battery pack systems for RV and related house-bank use. We do not sell air conditioners or inverters, we do not certify a pack against a named air-conditioner or inverter brand, and we do not claim that any pack is a drop-in solution for every cooling system. Nothing here is a wiring, soft-start installation, or power-on procedure.

Short answer
- Treat “parking air conditioning” as at least three electrical jobs, not one: a North American 115 VAC rooftop unit running through an inverter, a European 230 VAC rooftop unit running through an inverter, and a 12 V or 24 V parking cooler that draws DC from the house bank without that inverter stage.
- Use the air-conditioner maker’s running current (or input power) and, separately, any published starting or hard-start figure. Cooling capacity in watts or Btu/h is not the same number as electrical input.
- Check the inverter’s continuous rating at the temperature you actually expect, and its peak rating, against those figures. A worked official example in this page is the Victron MultiPlus-II 12/3000/120-50, which is a market inverter, not an LJY product.
- Check the battery’s continuous and peak discharge current from the datasheet for the selected configuration, at the house-bank voltage, including inverter losses. Capacity in amp-hours does not by itself start a compressor.
- Runtime is an energy calculation from measured or nameplate running power, inverter efficiency, other house loads and the usable energy of the selected pack. It is not a catalogue promise.
- Low-temperature charge limits still apply when the bank is recharged after a run. Heating and Bluetooth options can be discussed for the selected battery configuration; start temperatures, heater power, app brands, range and remote control are not stated on this page.
- Send the air-conditioner model, inverter model and the runtime target on the contact page.
The three electrical jobs buyers actually have
Buyers use several names for the same comfort problem: parking air conditioner, rooftop air conditioner, motorhome air conditioning, campervan or caravan air conditioning, and, in some truck and van markets, a parking cooler. The battery question changes with the electrical path.
115 VAC rooftop units (typical North American RV and many travel trailers). These are designed to run from shore power or a generator. Off-grid use means an inverter between the house battery and the air conditioner. Official running current is published as a 115 VAC figure. In the Dometic FreshJet 5 American leaflet (DOMETIC-FRESHJET5-AM-LEAFLET-2025Q2), the 13,500 Btu / 3,956 W cooling-capacity model is listed at 15.6 A current consumption, at 115 VAC, 60 Hz, single phase. The 3,956 W figure is rated cooling capacity, not electrical input.
230 VAC rooftop units (typical European motorhomes, campervans and caravans). Truma’s official page and product information for the second-generation Aventa compact list 1,700 W cooling power and 3.3 A cooling-mode power consumption at 230 V, with an operating voltage of 230–240 V, 50 Hz. Truma’s own FAQ states that operation while the vehicle is in motion is generally permitted if an appropriate power supply is ensured, “for example via a battery and an inverter.” That is evidence of a documented battery-and-inverter path. It is not a wiring method, and it is not an LJY compatibility claim.
12 V or 24 V parking coolers. These draw DC from a battery and do not use a large house inverter for the compressor. Dometic’s CoolAir RTX 1000 / RTX 2000 installation and operation manual (created 2 April 2026, modified 7 April 2026) lists, for the 12 V RTX 2000, a cooling capacity of 2,000 W, an input voltage of 10–15 V DC, current consumption of 10 A–58 A, and a rated power input of 650 W on the data plate. The same manual states a “Battery Capacity” of “180 Ah or greater.” Dometic’s product page for CoolAir RTX 2000 (item 9105306215) also states “up to 6 h running time,” “only 19 A consumption in Eco mode,” and JSON-LD current consumption of 5 A minimum and 60 A maximum cooling. Those Dometic figures are not a LiFePO4 runtime guarantee and are not LJY pack ratings. Use the document that belongs to the exact SKU you are buying.
A heat-pump mode, a second rooftop unit, a microwave on the same inverter, or a diesel or engine-driven parking air conditioner is yet another load. Do not copy a runtime from one path onto another.
What to read on the air-conditioner document
Before any battery quotation, collect the following from the air-conditioner nameplate and the manufacturer’s current leaflet or manual for that exact model:
- Input voltage and frequency (115 VAC 60 Hz, 230–240 VAC 50 Hz, or a DC voltage window).
- Running current or input power in the cooling mode you will actually use (and heating mode if the unit is a heat pump).
- Whether the published “watts” figure is cooling capacity or electrical input. On the FreshJet 5 13,500 Btu row, 3,956 W is rated cooling capacity; current consumption is 15.6 A at 115 VAC. On the Aventa compact, 1,700 W is cooling power; electrical current is 3.3 A at 230 V.
- Required circuit protection, if listed. That is a branch-circuit figure, not a battery BMS rating.
- Any starting, locked-rotor, inrush, or “hard start” statement. The FreshJet 5 leaflet lists “Hard start built in” as a feature. It does not publish a starting-current number in the table we reviewed. If the number is not on the document, do not invent a multiplier. Ask the air-conditioner supplier or have the installer measure a start on the intended inverter.
- Operating temperature range, especially for parking coolers. The RTX manual lists 5 °C to 52 °C for the 12 V RTX 1000 and RTX 2000.
Dometic and Truma products named on this page are typical market examples, not LJY products. Always re-read the manual for the revision you will install.
Official running figures used in the examples below
The arithmetic in the next sections uses only the official figures above, plus clearly labelled multiplication.
| Market example (not an LJY product) | What the maker publishes | Arithmetic on this page |
|---|---|---|
| Dometic FreshJet 5, 13,500 Btu row (SKUs 9620015924 / 9620015930 in the 2025 Q2 leaflet) | 115 VAC, 60 Hz; rated cooling capacity 13,500 Btu / 3,956 W; current consumption 15.6 A | 15.6 A × 115 V = 1,794 VA, if power factor is 1. Use a published watt or power-factor figure when the nameplate has one. |
| Dometic FreshJet 5, high-efficiency row (SKUs 9620015929 / 9620015932) | 11,000 Btu equivalent / 2,910 W cooling capacity; 10.8 A | 10.8 A × 115 V = 1,242 VA, same power-factor caveat. |
| Dometic FreshJet 5, 15,000 Btu cool-only row | 15,000 Btu / 4,396 W cooling capacity; 15.1 A | 15.1 A × 115 V = 1,736.5 VA, same caveat. |
| Truma Aventa compact, 2nd generation | Cooling power 1,700 W; cooling-mode consumption 3.3 A at 230 V; 230–240 V, 50 Hz | 3.3 A × 230 V = 759 VA. |
| Truma Aventa compact plus, 2nd generation | Cooling power 2,200 W; 5 A at 230 V | 5 A × 230 V = 1,150 VA. |
| Truma Aventa comfort, 2nd generation | Cooling power 2,500 W; 4.9 A at 230 V | 4.9 A × 230 V = 1,127 VA. |
| Dometic CoolAir RTX 2000, 12 V, manual | Cooling capacity 2,000 W; 10 A–58 A; rated power input 650 W; battery capacity 180 Ah or greater | Energy and current must be taken from the mode you will use (Eco versus boost). Do not treat 180 Ah as an LJY LiFePO4 size. |
Continuous power, peak power and a hot compartment
A 115 VAC rooftop unit in the 1,700–1,800 VA running class can sit inside the continuous rating of a 3 kVA-class inverter and still fail on starting current, or fail once the inverter derates in a hot RV.
The official Victron MultiPlus-II 120 V datasheet lists, for the 12/3000/120-50 (and the 24/3000 and 48/3000 columns in the same continuous-power rows):
- Continuous output power at 25 °C / 77 °F: 3,000 VA and 2,400 W
- Continuous output power at 40 °C / 104 °F: 2,200 W
- Continuous output power at 65 °C / 150 °F: 1,700 W
- Peak power: 5,500 W
- Maximum efficiency: 93 %
Those figures are Victron’s, for that product family, not LJY settings. The 1,794 VA FreshJet 5 13,500 Btu arithmetic sits below 2,400 W at 25 °C and still needs a margin for other AC loads. At 40 °C the same inverter’s continuous rating is 2,200 W. Peak power of 5,500 W is a short-duration figure; the datasheet row for this 12/3000 model does not state a duration next to 5,500 W (a neighbouring 12/4k column states 6 kW / 2 s). Do not assume a duration that the document does not give. Starting current still has to be confirmed against the inverter you will actually buy.
The same datasheet describes PowerAssist as a way to supplement limited shore or generator current from the battery during a peak, then recharge when the load falls. That is a shore-or-generator feature. It does not remove the need to size the battery and the inverter for an off-grid start and run.
For a 230 VAC Aventa compact, 759 VA running is a much smaller inverter and battery-current problem than a 1,794 VA 115 VAC rooftop unit. That is why regional equipment has to be named on the RFQ. It is not a reason to treat a European motorhome as “easy” without checking starting current, heat-pump current and other loads.
Battery current and energy — worked examples, not quotations
Convert AC running power to a minimum DC current only after you have an efficiency figure from the inverter maker. Victron’s 93 % is a published maximum efficiency, not a field measurement. Using it produces a best-case (lowest) battery current. Real current is higher.
For the FreshJet 5 13,500 Btu arithmetic of 1,794 VA, at 93 % and a 12.8 V nominal house bank:
- DC power floor = 1,794 / 0.93 ≈ 1,929 W
- DC current floor = 1,929 W / 12.8 V ≈ 151 A, plus every other 12 V load that is on at the same time
At a 25.6 V nominal (24 V class) house bank, the same floor is about 75 A, again plus other loads, and only if the inverter, charger and DC equipment are actually 24 V equipment. Changing only the battery voltage does not convert a 12 V coach.
A typical 12 V 100 Ah deep-cycle configuration on this site is listed with a 100 A continuous BMS as typical (12 V 100 Ah deep-cycle). 100 A at 12.8 V is 1,280 W of arithmetic current budget. That is below the 1,929 W floor above. It is the wrong current class for that 115 VAC rooftop path, even if the amp-hour label looks familiar.
The 12.8 V 200 Ah LiFePO4 battery with LCD lists a 250 A continuous BMS as typical and states that, at 12.8 V, this is roughly 3.2 kW of continuous discharge capability (250 A × 12.8 V = 3,200 W). That current class can be discussed for 2–3 kW inverter systems, as that product page already does. It is still not a promise that this pack will start a named air conditioner, hold voltage during the start, or run for a named number of hours. Dimensions, peak duration, cables, fusing and the datasheet for the exact build are confirmed per order.
Energy is a separate question from current. Four hours of 1,794 VA is 7,176 Wh on the AC side. At a 93 % maximum efficiency, the battery must supply about 7,716 Wh, not counting other house loads and not counting a less efficient real inverter. Nominal energy of a 12.8 V 200 Ah pack is 2,560 Wh (12.8 × 200). Nominal energy of a 12.8 V 300 Ah pack is 3,840 Wh (12.8 × 300). Neither figure is a four-hour energy budget for that 13,500 Btu rooftop example. A honest procurement outcome may be a larger bank, a 24 V or higher architecture designed as a system, a lower-input 230 VAC inverter air conditioner, a 12 V parking cooler with a documented current range, a shorter runtime, or a residual dependence on a generator or shore connection. This page will not invent a pack size that “runs any RV air conditioner for a weekend.”
For a 12 V parking cooler, start from the maker’s current range and rated power, not from cooling capacity. The RTX 2000 manual’s 650 W rated power input and 10 A–58 A window, and the product page’s 19 A Eco-mode statement, describe different operating points. Four hours at 650 W would be 2,600 Wh of input energy — close to one 12.8 V 200 Ah nominal pack — but only if the unit actually averages 650 W. Boost current at the top of the 10 A–58 A (manual) or 60 A (product-page maximum) range has to fit the BMS and the wiring the installer designs. Dometic’s “180 Ah or greater” and “up to 6 h” statements stay attributed to Dometic. They do not become LJY LiFePO4 ratings, and the manual does not state a chemistry against that 180 Ah line.
Optional heating and Bluetooth on the house bank
LiFePO4 cells should not be charged below 0 °C. Existing LJY pages already cover the chemistry limit, low-temperature charge cutoff, and the buying logic for self-heating packs; see the heated LiFePO4 battery buying guide and the RV converter LiFePO4 charging guide. This page does not repeat those documents.
If the vehicle must recharge the house or leisure bank in freezing weather after a cooling or heat-pump run, say so on the RFQ. Heating and Bluetooth options can be discussed for the selected battery configuration. They are not standard on every LJY pack. This page does not state a heater start or stop temperature, heater power, app brand, wireless range, a list of monitored fields, a certification, or remote control. Those items, if required, are confirmed per project. A configured example of a cold-climate 12 V house pack is the 12 V 100 Ah heated LiFePO4 battery, whose heating engagement temperature and power are “to be confirmed per order” on that page.
Bluetooth, if specified, is a monitoring option for the selected configuration. It does not replace a recorded acceptance test of starting current and runtime, and it does not make a voltage-only fuel gauge accurate by itself.
What to send when you enquire
Use the existing contact page. A usable RV or caravan air-conditioning RFQ includes:
- Vehicle type and market (RV, motorhome, campervan, caravan or trailer; North America, Europe, or another region).
- Air-conditioner make, model, SKU and the leaflet or manual revision, plus whether it is 115 VAC, 230 VAC, or a 12 V / 24 V parking cooler. Attach the page that lists running current or input power.
- Starting, hard-start or locked-rotor data if the manufacturer publishes it; otherwise say that it is not published and will be measured on the intended inverter.
- Inverter or inverter/charger make, model, continuous and peak ratings, and the temperature at which those ratings apply.
- House-bank voltage (12.8 V, 25.6 V, or another confirmed system voltage) and the target runtime at a stated ambient, with other loads listed (fridge, lights, fans, water pump, device charging).
- Charge sources that will refill the bank (shore converter, solar, alternator / DC-DC, generator). Compatibility of those paths is covered on the converter and DC-DC guides; name the models here rather than assuming a lead-acid converter is suitable.
- Compartment dimensions, weight limits and terminal constraints. Physical fitment is not this page’s catalogue; see the BCI group-size page and the house versus starter guide.
- Climate and whether heating and Bluetooth options should be discussed for the selected battery configuration.
- Quantity, whether this is a sample, a dealer stock item, or an OEM programme, and the destination market so that documents can be confirmed. No certificate, lead time or current rating is assumed until it is written for that build.
Acceptance — what to record, not how to energize
Acceptance belongs to the buyer and a qualified installer. This page lists records, not connection steps.
Before a production or fleet decision, record at least:
- The exact air-conditioner, inverter and battery configurations, including firmware or BMS software if the suppliers identify it.
- A start event on the intended inverter: whether the compressor started, whether the inverter or BMS entered a protection state, and the peak current and voltage the instruments actually showed.
- A steady cooling run at a stated thermostat setting and ambient: running current or inverter load, battery current and voltage, and other loads that were on.
- Runtime to an agreed state of charge, with the energy used compared to the datasheet usable energy, not only to the amp-hour label.
- Temperature of the installation space and, if the configuration provides it, the battery temperature used by the BMS. If a low-temperature charge inhibit or an optional heater is part of the order, record whether charging was allowed or blocked at the temperature you tested.
- If Bluetooth monitoring was specified, record that the agreed interface connected on the sample. Do not treat an app screenshot as a substitute for the current and runtime log.
A sample that starts once on a cool bench is not evidence for a hot-roof, low-state-of-charge, or freezing-morning production vehicle.
What this page does not decide
- Cable size, fuse or breaker selection, inverter programming, soft-start device fitting, or any modification of the vehicle or the air conditioner.
- Whether a particular LJY pack is approved by Dometic, Truma, Victron or any other brand.
- A universal runtime, a weekend “rule of thumb,” or a market-size claim.
- Chassis starter-battery selection. That is a different purchase; see RV house versus starter and the 12 V / 24 V starter series.
Frequently asked questions
Can a 12 V 100 Ah house battery run a rooftop air conditioner?
Not as a general rule. For the FreshJet 5 13,500 Btu official current of 15.6 A at 115 VAC, the best-case DC current floor in the worked example is about 151 A at 12.8 V. A typical 100 A BMS on a 12 V 100 Ah pack is the wrong current class for that path. A smaller 230 VAC rooftop unit or a 12 V parking cooler may be a different calculation — use that unit’s document.
How long will a 200 Ah battery run the air conditioner?
Only as long as the energy math and a test say. Nominal energy of a 12.8 V 200 Ah pack is 2,560 Wh. Four hours of the 1,794 VA rooftop example needs about 7,716 Wh at a 93 % maximum inverter efficiency, before other loads. Do not buy on a promised hour figure that has no load list behind it.
Is a parking cooler easier on the battery than a rooftop unit?
It can be, because it avoids a large inverter stage and may have a documented Eco-mode current, but the manual still publishes a wide current window (10 A–58 A for the 12 V RTX 2000). Size for the mode you will use, including the maximum the datasheet allows, and keep Dometic’s own 180 Ah / 6 h language attributed to Dometic.
Do I need a self-heating or Bluetooth battery to run the air conditioner?
No. Those options do not start a compressor. Heating and Bluetooth options can be discussed for the selected battery configuration when you need cold-weather charging or a monitoring interface. They are not required for every air-conditioning purchase and are not standard on every pack.
Can I connect a LiFePO4 pack and “drop it in” for air-conditioner use?
No general drop-in claim is made here. Fitment, inverter compatibility, BMS current, charge sources and a recorded start-and-run test all have to be confirmed for the system you are buying.
Sources
- Dometic, FreshJet 5 American leaflet, document mark DOMETIC-FRESHJET5-AM-LEAFLET-2025Q2. Official file retrieved 17 November 2026, Asia/Shanghai, HTTP 200: https://media.dometic.com/externalassets/02-0206-020633-020633047_9620015929_133709.pdf. Used for 115 VAC / 60 Hz input; 13,500 Btu / 3,956 W and 15.6 A; high-efficiency 11,000 Btu equivalent / 2,910 W and 10.8 A; 15,000 Btu / 4,396 W and 15.1 A; “Hard start built in.”
- Truma, Aventa compact (2nd generation) product page, retrieved 17 November 2026, HTTP 200: https://www.truma.com/products/air-conditioning-systems/aventa/aventa-compact-2-generation/. Used for 1,700 W cooling power; 3.3 A cooling-mode consumption at 230 V; 230–240 V, 50 Hz; FAQ language on battery and inverter supply.
- Truma, Product info – 2nd generation Aventa roof-mounted air conditioning systems, August 2024 retail PDF, retrieved 17 November 2026, HTTP 200: https://portal.truma.com/wp-content/uploads/2024/08/truma-airconditioning-systems-product-information-aventa-next-gen-0824-retail-en_us.pdf. Used for compact / compact plus / comfort cooling power and 3.3 A / 5 A / 4.9 A consumption.
- Dometic, RTX1000-2000 Parking Cooler Installation and Operation Manual, created 2 April 2026, modified 7 April 2026, retrieved 17 November 2026, HTTP 200: https://media.dometic.com/externalassets/rtx2000_9600028490_76954.pdf. Used for RTX 2000 12 V: 2,000 W cooling capacity; 10 V–15 V; 10 A–58 A; 650 W rated power input; “180 Ah or greater”; 5 °C to 52 °C.
- Dometic, CoolAir RTX 2000 product page, item 9105306215, retrieved 17 November 2026, HTTP 200: https://www.dometic.com/en/professional/product/dometic-coolair-rtx-2000-9105306215. Used for “up to 6 h running time,” “only 19 A consumption in Eco mode,” and JSON-LD current min 5 A / max 60 A. Where this page and the manual differ, the exact SKU document governs.
- Victron Energy, MultiPlus-II Inverter/Charger 120 V datasheet, retrieved 17 November 2026, HTTP 200: https://www.victronenergy.com/upload/documents/Datasheet-MultiPlus-II-120V-EN-.pdf. Used for 12/3000/120-50 continuous 3,000 VA / 2,400 W at 25 °C, 2,200 W at 40 °C, 1,700 W at 65 °C; peak 5,500 W; maximum efficiency 93 %; PowerAssist description.
Limitation: the Dometic consumer product URLs for Brisk II and Blizzard NXT returned a category page in this retrieval environment, so those two model names are not used as numerical sources. No market-size or search-volume figures were used or invented.
Related guides
- RV battery solutions
- RV battery selection guide
- RV lithium battery system design guide
- RV converter LiFePO4 charging guide
- Alternator and DC-DC charging for LiFePO4
- Heated LiFePO4 battery buying guide
- 12.8 V 200 Ah LiFePO4 battery with LCD
- 12 V 300 Ah LiFePO4 battery
- 24 V 200 Ah LiFePO4 battery for RV and caravan
- RV house battery versus starter battery
**Send the air-conditioner model, the inverter model and the runtime target on the contact page.**
Send the air-conditioner model, the inverter model and the runtime target on the contact page · WhatsApp +86 159 8945 0735
