Small-shop POS, router and camera backup — a LiFePO4 pack and system acceptance checklist
When the grid drops, a small shop does not need the whole building to stay lit. It needs the till, the card terminal, the router or optical network terminal, and the cameras or recorder that keep the premises visible. Buyers often search for a “48V lithium battery” and hope the pack is the system. It is not. This page is a procurement and acceptance checklist for a low-voltage LiFePO4 pack plus the inverter, charger or uninterruptible power supply (UPS) that will actually carry those critical loads.
LJY Energy is a LiFePO4 supplier and OEM/ODM coordinator in Shenzhen; we are not a factory. We supply battery packs. We do not sell point-of-sale terminals, routers, cameras, or a named-brand UPS, and we do not claim that a pack is universally compatible with those devices. Nothing on this page is a wiring, adapter or modification procedure. Typical voltages and currents below are taken from published LJY product pages and must be confirmed on the order datasheet.

Short answer
- Start from a written critical-load list: POS and receipt printer, router or ONT, network video recorder and cameras, and only the extra outlets you truly need. Leave air conditioning, kitchen equipment and general lighting off that list unless you have measured them and accepted the larger system.
- Average watts and the required hours set pack energy. Startup and inrush — printers, PoE switches, camera power supplies — set the inverter or UPS power rating. A pack capacity figure alone does not clear either check.
- A storage LiFePO4 pack in the 12.8V, 25.6V or 51.2V (48V-class) families is not a drop-in replacement for a UPS maker’s approved external battery pack, and it is not a telecom −48V plant battery. Those are different voltage windows and, in the telecom case, a different polarity. See 48V vs 51.2V vs −48V.
- Climate is a charge boundary. Published typical pages for 12V-class packs state that charging should not take place below 0°C unless the ordered configuration includes low-temperature charge protection or heating.
- Standby matters in a shop: the pack may sit on a charger for days between outages. The charger’s float or storage profile must sit inside the pack’s charge window, and BMS standby draw should be confirmed on the datasheet.
What this page covers, and what it does not
This page is for small retail or service premises that need a defined set of AC or DC critical loads to ride through a short or medium outage. It is not a home energy-storage design, not a data-centre or AI-rack design, not a vehicle or marine install, and not a hospital or clinic specification. We do not claim industrial or medical grade on this page.
Location landing pages already exist for shop backup in some markets. They are not a substitute for the load, startup, inverter, climate and acceptance checks below.
Build the critical-load list first
Write every device that must stay up, its supply type (AC outlet, DC jack, or Power-over-Ethernet from a switch), and a measured or nameplate watt figure. A typical shop list looks like this — the numbers must come from your devices, not from this page:
- Point-of-sale terminal and receipt printer (printers often dominate startup).
- Payment or barcode peripherals that die if the till stays up but the USB hub does not.
- Router, ONT or a small network switch — without these, a “working” POS still cannot take a card.
- NVR or mini recorder, plus cameras if they are not powered from that recorder’s PoE ports.
- One modest lighting or alarm outlet only if you have chosen to include it.
If a device is DC-native (a 12V camera or radio), decide whether it will be fed from a DC distribution point on the pack’s voltage class or from an AC-DC power supply on the inverter. Mixing both without writing the voltage window down is how packs and chargers get mis-ordered.
Load, startup and runtime are three checks
Load. Sum the running watts of the critical list. That figure, times the hours you must cover, times a margin you agree in the quotation, sets the usable energy the pack must deliver. Do not treat a catalogue amp-hour figure as usable energy until the depth of discharge and the inverter efficiency (if AC loads are used) are written down.
Startup. Receipt printers, some POS power-supplies, PoE switches and camera adaptors can draw a short surge well above their running watts. The inverter or UPS continuous and surge ratings, and the pack’s continuous and peak discharge ratings, must be checked against that surge. A typical published figure on the 12V 100Ah deep-cycle product page is a continuous discharge of 100A and a peak of 200A for ≤3 s — marked typical, not a guarantee for every unit, and not a claim that this SKU is the right shop pack.
Runtime. Agree the outage duration you are buying: the time to finish a queue, close the till, and keep cameras recording, or a longer ride-through. Runtime is accepted against the agreed load list, not against an empty-shop test or a single-device bench discharge unless that is what the quotation says.
Inverter or UPS: choose a system path
There are two common system paths. They are not interchangeable on a purchase order.
- Inverter / charger + storage pack. A hybrid or off-grid inverter, specified by its own manufacturer, charges and discharges a LiFePO4 bank in a stated voltage class — often 25.6V (24V class) or 51.2V (48V class) for AC shop loads. Our 24V 100Ah page lists a typical nominal of 25.6V (8S) and a typical charge voltage of 28.4–29.2V. The 48V 100Ah energy-storage page lists a typical nominal of 51.2V (16S), sold in the 48V ESS class, at 5.12kWh per 100Ah module. The inverter’s battery voltage window, charge voltage and communication (if closed-loop) must be read from the inverter datasheet and confirmed in the quotation. LJY does not certify compatibility with named inverter brands on this page.
- A UPS that already has an approved battery architecture. If the shop already uses a brand UPS, an external pack is usually a manufacturer accessory, not a generic storage module. A 19-inch or “48V” LiFePO4 pack is not an approved UPS external battery module unless that UPS maker documents the exact combination. This page does not provide adapters or pin-outs.
Do not feed a telecom −48V DC plant from a 48V-class storage pack, and do not assume a shop inverter bank can stand in for a −48V rectifier plant. If the site is actually a communications room with a negative-voltage plant, stop and use the telecom pages linked below.
Climate and where the pack will sit
Shops put batteries in a storeroom, a counter cupboard, an outdoor cabinet, or an unconditioned back room. Charge temperature is the first climate bound. The 12V 100Ah deep-cycle page states a typical charge range of 0°C to 45°C, and says not to charge below 0°C unless low-temperature protection is fitted. The 12V 100Ah heated page states that LiFePO4 cells must not be charged below 0°C, and that a heated configuration warms the cells before charge is allowed; heating engagement and power are confirmed per configuration. A 24V-class page lists low-temperature charge cut-off below 0°C, with a self-heating pad, as optional.
Discharge ranges, enclosure ingress ratings and cabinet ventilation are confirmed on the order datasheet. An outdoor wall-mounted 51.2V format exists as an enclosure option on a separate product page; the IP rating of a given build is confirmed per project, not assumed from the page title.
Standby behaviour and what to accept
A shop backup pack may spend most of its life waiting. Before you accept a delivery, the quotation should already have fixed:
- The charger or inverter storage / float behaviour, and that it lies inside the pack’s documented charge window (for example, typical 12V-class absorption 14.2–14.6V on the 12V 100Ah deep-cycle page — confirm the value on your datasheet).
- Whether the BMS remains powered during standby, and any parasitic draw the datasheet states. Do not invent a monthly self-discharge figure for a 24V or 51.2V pack from a 12V page. Where a 12V page publishes a typical self-discharge of <3% per month at 25°C, treat it as typical for that page only.
- The acceptance test you will actually run: a discharge at the agreed critical-load list, or another method written in the quotation. This page does not publish a universal factory test or a certified runtime.
- The documents that ship with the order. UN38.3, MSDS and market certificates are described on product pages as coordinated or confirmed per order — not as a blanket claim for every configuration.
What to send when you enquire
- The critical-load list, running watts (measured if you have them), and any known startup or inrush figures.
- The hours of backup you are buying, and whether the till must complete a sale or only shut down cleanly.
- The intended system path: inverter/charger model (with its battery voltage window) or UPS model and what its maker approves.
- AC versus DC loads, and the pack voltage class you think you need — or a request that we help you choose among 12.8V, 25.6V and 51.2V storage classes, not −48V.
- Where the pack will be installed, the temperature range, and whether charge may be needed below 0°C.
- Communication needs (for example RS485 or CAN) only if an inverter closed-loop setup is planned; these are optional on several published SKUs and confirmed per order.
Send the load list, runtime target and inverter or UPS model on the contact page.
What this page does not decide
- It does not approve a named POS, camera, router, inverter or UPS combination.
- It does not specify fire-code, electrical-licence or insurance requirements for your country; those are not invented here.
- It does not cover clinic, hospital or laboratory loads.
- It does not convert a storage pack into a telecom −48V battery, or into a UPS external battery module.
Frequently asked questions
Can I put a LiFePO4 pack into the battery bay of the shop UPS?
Only if the UPS maker documents that exact pack as an approved accessory. Otherwise, treat the UPS and a storage pack as different system paths. We do not provide a modification method.
Is a 51.2V pack the same as a 48V pack for a shop inverter?
A 16S LiFePO4 module is commonly sold in the 48V energy-storage class and labelled 51.2V nominal. That is not the same thing as a marketing “48V” label, and it is not a telecom −48V bus. Confirm the inverter’s permitted battery window against the order datasheet. The voltage guide linked below explains the labels.
Do I need a heated pack in a shop storeroom?
Only if the pack may be charged below 0°C in that room. If the room stays above the charge-temperature minimum in the datasheet, a heated option may be unnecessary. If it may not, low-temperature charge protection or heating should be in the RFQ, not added after a winter outage.
Will LJY certify this as an industrial backup system?
No. This page does not claim industrial or medical grade. We quote a pack configuration and the documents that belong to that order.
Sources
- LJY Energy, 12V 100Ah deep-cycle LiFePO4 battery (typical 12.8V, 100Ah, 1,280Wh; charge 14.2–14.6V; charge 0°C to 45°C; typical peak 200A for ≤3 s; typical self-discharge <3% per month at 25°C): https://ljyenergy.com/12v-100ah-deep-cycle-lifepo4-battery/
- LJY Energy, 12V 100Ah heated LiFePO4 battery (do not charge below 0°C; heating parameters confirmed per configuration): https://ljyenergy.com/12v-100ah-heated-lifepo4-battery/
- LJY Energy, 24V 100Ah LiFePO4 battery (typical 25.6V / 8S, 2.56kWh, charge 28.4–29.2V; low-temperature cut-off / heating optional): https://ljyenergy.com/24v-100ah-lifepo4-battery/
- LJY Energy, 48V 100Ah energy-storage battery (typical 51.2V / 16S, 5.12kWh, 48V ESS class): https://ljyenergy.com/48v-100ah-lifepo4-energy-storage-battery/
- LJY Energy, 48V vs 51.2V vs −48V: https://ljyenergy.com/48v-vs-51-2v-vs-minus-48v-lifepo4/
- LJY Energy, outdoor IP65-class wall-mounted 51.2V format (IP rating confirmed per project): https://ljyenergy.com/outdoor-ip65-wall-mounted-lifepo4-battery-51-2v/
- LJY Energy, contact: https://ljyenergy.com/contact/
Source limitation: product figures used above are marked typical, optional, or confirmed per order on those pages. They are not reused here as guarantees or as a compatibility matrix. No market-size, search-volume or certification claim was added.
Related guides
- 48V vs 51.2V vs −48V LiFePO4 — storage labels versus a telecom −48V plant
- Telecom base station rack battery — only if the site is a −48V DC plant, not a shop inverter bank
- 24V 100Ah LiFePO4 battery — published 25.6V-class typical data
- 48V 100Ah energy-storage battery — published 51.2V-class typical data
Send the load list, runtime target and inverter or UPS model on the contact page
