LiFePO4 Batteries for Wheelchairs and Scooters

A power wheelchair or a mobility scooter does not run on a single battery. Almost every chair and scooter on the road runs on 24 volts, and that 24 volts comes from two 12-volt batteries wired in series — which means the sizing question is a system question, not a single-battery question: which pair fits the tray, whether the two batteries match, and whether the charger suits the chemistry you are moving to. The pair size follows the vehicle. A folding travel scooter usually carries two 12V 12Ah batteries; a mid-size everyday scooter takes two 12V 20Ah; a heavy-duty chair or scooter takes two 12V 35Ah batteries in the U1 group size; and a full-size power chair takes the larger 22NF (55Ah) and Group 24 (about 74Ah) cases. Four things decide whether a new battery fits: the voltage, the capacity in amp-hours, the physical size of the box it sits in, and the terminal type, F1 or F2 — and on a 24V system there is a fifth rule that matters more than any of them: both batteries must be replaced together, as a matched pair, never one old and one new. This guide covers the system: how to read the pair size from your chair, how to match the group size to the tray, and how to check the charger before you swap chemistries. Every figure here is a planning range — the numbers that size your battery are the ones on your own chair manual and battery tray.

LJY Energy is a LiFePO4 battery supplier and OEM/ODM coordinator in Shenzhen; we are not a factory. This guide covers the battery side only — which pair size matches a chair or scooter, and which charger check comes before a chemistry swap. The chair, the scooter, the controller and the installation come from your dealer or installer, and the charging setup must match the battery chemistry: a charger built for sealed lead-acid does not suit a lithium pack, so confirm the charger with the installer before you swap chemistries. Our 12V drop-in ladder runs from 12Ah travel packs through 20Ah and 35Ah to 50Ah and 100Ah for larger chairs, and 24V packs are available as matched pairs or as single units — the size that fits your tray is confirmed per project in the quotation. Cycle life and warranty are confirmed per model in the same way: they depend on the cells and the BMS of the pack you order, so this guide makes no cycle or warranty promise of its own. These are deep-cycle batteries, not starter batteries, and every order is confirmed in writing before production.

LiFePO4 cells for wheelchair and scooter battery packs
Photo: Yo-Co-Man, Wikimedia Commons, CC BY-SA 4.0 (resized, WebP). Illustrative image, not an LJY product.

Sizing reference

Power chair and scooter system voltage24 V
Travel scooter battery pair2 × 12 V · 12 Ah
Mid-size scooter battery pair2 × 12 V · 20 Ah
Heavy-duty battery pair2 × 12 V · 35 Ah
Drop-in nominal voltage12.8 V
Small pack energy154 Wh
Large pack energy448 Wh
Series pair energy896 Wh
Reference pack, single unit25.6 V · 20 Ah · 512 Wh

Pair specifications live on the 24V 20Ah LiFePO4 battery page; confirm values on the product page and in the written quotation for your project.

Worked example

A 12 Ah pack holds about 154 Wh. Stepping up to a 35 Ah pack in the same 12 V class holds about 448 Wh — roughly 2.9 times the energy, with the same voltage and the same four things to check before you order. Two 35 Ah batteries wired in series make a 24 V system holding about 896 Wh — the pair, not the single battery, is the unit that sizes a chair. A 24 V 20 Ah pack holds 512 Wh: at a 250 W draw that is about 2 hours of driving, and since a motor only draws its rated watts at full load, a real trip usually runs longer than the nameplate math suggests. Size from your own chair manual and battery tray, not from these examples, and confirm the pack size per project in the quotation.

What to send before a proposal

  • Chair or scooter make and model, system voltage, and the size and terminal type of the batteries already installed — one battery or a matched pair
  • Battery tray dimensions and group size — U1, 22NF or Group 24 — and how much room the tray has for a taller or wider case
  • How many hours a day the chair or scooter runs, the terrain it covers, and the charger already on hand — its chemistry setting decides whether it stays or goes

Request a sizing

Send the chair or scooter make and model, the system voltage, and the size and terminal type of the batteries already installed — one battery or a matched pair — plus the tray dimensions and group size if you know them. LJY Energy will work out the matching pair and answer it in the quotation itself — which is where it belongs. If the chair still runs its original lead-acid charger, tell us before you order: the charger check is part of the sizing, not an afterthought. Size from your own manual and tray, not from the ranges on this page.

Battery power circuit board with coloured wiring
Photo: Dilshan Jayakody, Wikimedia Commons, CC BY-SA 2.0 (resized, WebP). Illustrative image, not an LJY product.

Request a wheelchair and mobility scooter battery quote · WhatsApp +86 159 8945 0735