JK-PB2A16S-15P/20P: inverter CAN, RS485 and pin-out checklist

The JK-PB2A16S-15P and JK-PB2A16S-20P are inverter / energy-storage BMS boards. Anyone searching for a JK-PB2A16S-15P 20P inverter CAN RS485 checklist needs the official series ranges, the port roles and the official RJ45 pin-out, not a compatibility verdict inferred from a 16S label or from another maker’s cable. On the official PB board, CAN pin 4 is CANL and pin 5 is CANH — the opposite of some other makers. A port name is not an approval.

LJY Energy is a LiFePO4 supplier and OEM/ODM coordinator in Shenzhen, not a factory, and we do not claim to supply JK BMS products. This page quotes the official JK-PB2A16S-15P and 20P product pages and the official inverter-BMS communication page only. Protocol, cable and inverter settings are confirmed per project. We do not publish a compatibility verdict. The 20P is listed as a 200 A class; this page does not treat 200 A as a confirmed continuous-discharge rating unless the document shipped with the board states it.

A commercial street, used only as general context, not as a pairing claim with a JK BMS board
Photo: Visuals by làná, Wikimedia Commons, CC BY-SA 4.0 (resized, WebP). Illustration, not an LJY product.

Request a JK-PB2A16S pin-out and port checklist · WhatsApp +86 159 8945 0735

Facts taken from the official JK pages

PointWhat the documents stateThe installer still confirms
Chemistry and seriesLFP 8–16S, NMC 7–16S, LTO 14–16S; 2 A active balancethe chemistry and series of this pack
Current class15P listed at 150 A continuous discharge; 20P listed as a 200 A classthe rating in the document shipped with that board
PortsCAN and RS485-1 for inverter communication; RS485-2 for parallel packs or PC software; also Bluetooth and a displayone intended inverter method, not a port name as an approval
RJ45 pin-outCAN pin 4 CANL, pin 5 CANH; RS485-1 pins 1/8 B, pins 2/7 Athe cable against this official pin-out, which is the opposite of some other makers
Verdictnone is published on this pageprotocol, cable and inverter settings confirmed per project

A 16S label, or a CAN cable copied from another maker, is not an approval. CANL on pin 4 and CANH on pin 5 must be checked before the cable is landed. Protocol is confirmed per inverter model and firmware.

What the assembler or installer sends before a proposal

  • Whether the board is a 15P or a 20P, and the revision if known.
  • Pack chemistry and series count, against the official ranges.
  • Whether the inverter link is intended for CAN or for RS485-1 — not inferred from a port name.
  • The planned RJ45 cable, checked against CANL on 4 and CANH on 5.
  • Inverter model and firmware, and written confirmation if available.

Record the pin-out on a first board, then repeat it

Assemblers who record the official pin-out and the intended port on a first JK-PB2A16S board, rather than copying another maker’s cable, avoid a silent swap of CANH and CANL after several packs are already wired. Prices and lead times only in a quotation.

A highway, used only as general context, without any compatibility claim
Photo: jbdodane, Wikimedia Commons, CC BY 2.0 (resized, WebP). Illustration, not an LJY product.

How we proceed

Board class, series count and intended port → checklist against the official JK pages → first test → later packs. Prices and lead times only in the formal quote. We do not publish a compatibility verdict.

Send the board class and pack data and request a checklist

LJY Energy, Jack Lai. Unit 705, Building 1, Lecai Industrial Park, 10 Kaijing Road, Longtian Street, Pingshan District, Shenzhen 518122, China. +86 159 8945 0735.