In Dar es Salaam, Arusha, Mwanza and nearby towns, boda and bajaji fleets are moving toward pack swap so riders do not wait on a charger. Anyone searching for a battery swap pack for boda or bajaji networks in Tanzania needs more than a 60V or 72V label (60V and 72V supply confirmed per project). A pack that is to move between vehicles and cabinets must match series count, charge cut-off, connector, mechanical size and the BMS-to-cabinet protocol. This page is about interchangeable swap packs, not a single-vehicle conversion pack that never leaves its own charger.
LJY Energy is a LiFePO4 supplier and OEM/ODM coordinator in Shenzhen, not a factory. We do not supply cabinets, vehicles or chargers. We coordinate 51.2V 16S packs as the 48V-class reference. Any 60V or 72V pack is confirmed per project: the table below separates nominal voltage, charge cut-off, series count and BMS, because a voltage name is not a swap specification. Protocol and pin-out between the pack BMS and the cabinet are confirmed in writing for that network, not inferred from a similar model name.

Request a swap-pack checklist for a Tanzanian network · WhatsApp +86 159 8945 0735
What the operator defines per pack family
| Point | Why it matters | Confirmed per project |
|---|---|---|
| 48V-class / 51.2V 16S | common reference for many bajaji and e-motorcycle conversions | Ah, connector and cabinet protocol |
| 60V or 72V class | only if the vehicle and cabinet actually use that window | confirmed per project; see the series table |
| Charge cut-off | must match the cabinet charger, not a name on the pack | volts at the connector |
| Connector and size | the pack must seat in more than one cabinet and vehicle | drawings and a first-article fit |
| BMS-to-cabinet protocol | the cabinet must see the pack data | protocol and pin-out in writing |
A voltage name is not a swap specification. 60V and 72V packs are confirmed per project after nominal voltage, charge cut-off, series count and BMS are written down and checked against the charger and the controller.
Nominal voltage, charge cut-off, series count and BMS
A 48V, 60V or 72V nameplate (60V and 72V supply confirmed per project) does not say how many cells are in series or where a cabinet charger must stop. The table multiplies public per-cell values by the series count: LiFePO4 from the EVE LF304 datasheet, NMC from the Samsung SDI 18650-25R datasheet, and lead-acid from Battery University charge limits. Every 60V or 72V pack is confirmed per project.
| Chemistry and series | Nominal | Charge cut-off | BMS configuration |
|---|---|---|---|
| LiFePO4 16S (3.2V / 3.65V per cell) | 51.2V | 58.4V | 16S board |
| LiFePO4 20S | 64.0V | 73.0V | 20S board |
| LiFePO4 24S | 76.8V | 87.6V | 24S board |
| NMC 16S (3.6V / 4.2V per cell) | 57.6V | 67.2V | 16S board, NMC limits |
| NMC 20S | 72.0V | 84.0V | 20S board, NMC limits |
| Lead-acid 60V (5 × 12V, 30 cells, 2.30–2.45V per cell) | 60V | 69.0–73.5V | no BMS; LiFePO4 replacement confirmed per project |
| Lead-acid 72V (6 × 12V, 36 cells) | 72V | 82.8–88.2V | no BMS; LiFePO4 replacement confirmed per project |
A 60V lead-acid set charges up to about 73.5V, while a 20S LiFePO4 pack stops at 73.0V, so 60V supply is confirmed per project and each station charger is set to the pack, not the name. A 16S BMS cannot protect a 20S pack. We never infer compatibility from a voltage name.
What the operator sends before a proposal
- Vehicle nominal voltage and the charger’s cut-off voltage.
- Series count and chemistry the network has already standardised, if any.
- Connector type and the mechanical envelope of the pack.
- The cabinet’s communication protocol, if the maker has published it.
- How many stations and vehicles should share the same pack family.
Prove one pack family at two cabinets
Networks that seat a first pack family in two cabinets and on two vehicles, and record the cut-off and the protocol, then freeze that family, avoid a silent mismatch after dozens of packs are already in the field. Prices and lead times only in a quotation.

How we proceed
Voltage window, series, connector and protocol → checklist and pack proposal → first-article swap → roll-out. Prices, quantities and lead times only in the formal quote.
Send the vehicle and cabinet data and request a proposal
LJY Energy, Jack Lai. Unit 705, Building 1, Lecai Industrial Park, 10 Kaijing Road, Longtian Street, Pingshan District, Shenzhen 518122, China. +86 159 8945 0735.
