A 24V 200Ah LiFePO4 battery is the standard replacement size for a Class III pallet truck and a small warehouse truck: 200 Ah at a nominal 24 V, a 20 to 29.2 V working range, and a 400 A maximum discharge current (2C, per supplier brochure). It suits trucks built around a 24 V system, charges between shifts, and with opportunity charging during breaks it covers a full shift of typical warehouse work on one pack. Three checks decide whether it fits your truck: the voltage window the controller accepts, the shift pattern and charging windows, and whether the truck’s peak draw stays inside the pack’s limits — or whether the job needs a step up to 48 V. This page walks through all three, with the numbers a buyer needs before asking for a quotation.
The working range matters more than the nominal label. A 24 V LiFePO4 pack works between 20 and 29.2 V, and the truck’s controller and lift motor must accept that whole window — a truck tuned for a lead-acid voltage curve can cut out early or throw a low-voltage fault if the range is not checked first. The 400 A maximum is a short-peak figure (2C, per supplier brochure): it covers the moment the truck lifts and accelerates at once, but the shift length is set by the average draw, not the peak. Opportunity charging is where this chemistry earns its place in a warehouse: top the pack up during breaks and between shifts instead of swapping it out, and one pack per truck covers a single-shift operation; a second pack per truck covers two shifts with no charging window. Start with one pack per truck and add a second pack only where the shift pattern needs it — the pack size is confirmed per project in the quotation. LJY Energy is a LiFePO4 battery supplier and OEM/ODM coordinator in Shenzhen; we are not a factory. Your configuration, documents and price are confirmed per project in writing.

24V 200Ah forklift battery at a glance
| Nominal voltage — 24 V system (25.6 V nominal) | 24 V |
| Working voltage range — 20 to 29.2 V | 20–29.2 V |
| Capacity — 200 Ah | 200 Ah |
| Maximum discharge current — 400 A (2C, per supplier brochure) | 400 A |
| Energy at nominal voltage — 5.12 kWh | 5.12 kWh |
| Cell configuration — 8 cells in series | 8S |
| Discharge rate — 2C maximum | 2C |
| Step-up option — 48 V for heavier trucks | 48 V |
For the full 24V pallet-truck range — other capacities in the same series — see the 24V pallet truck LiFePO4 battery series.
Worked example: one shift on a 200 Ah pack
A Class III pallet truck drawing 80 A on average uses 80 Ah per hour of driving, so a 200 Ah pack covers about 2.5 hours of continuous driving before it needs a recharge. Real warehouse work is not continuous driving — the truck idles, loads and waits between runs — so with opportunity charging during breaks, one pack typically covers a full single shift. The 400 A maximum (2C, per supplier brochure) covers the short peaks when the truck lifts and accelerates at once; it is the average draw, not the peak, that sets the shift length. If the truck runs two shifts back to back with no charging window, or the lift motor regularly draws near the pack’s continuous limit, that is the sign to step up to a 48 V system, where the same power needs half the current.
What to check before you order
- Voltage match: confirm the truck runs a nominal 24 V system and its controller accepts the full 20 to 29.2 V working range — a pack that only matches the nominal label can still trip a low-voltage fault under load.
- Shift pattern: one shift with overnight charging, or two shifts back to back — a second pack per truck covers two-shift work with no charging window, and opportunity charging during breaks stretches a single pack across a full shift.
- Peak draw: check the combined lift and drive peak against the 400 A maximum (2C, per supplier brochure). If sustained draw sits near the limit, step up to 48 V rather than running the pack at its ceiling.
- Physical fit: tray size, pack weight and counterweight, and the connector type all decide whether the pack fits the truck — send the truck model and tray dimensions with the enquiry so the fit is confirmed per project in the quotation.
Discuss forklift battery requirements
The 24 V decision is really a duty decision. A single-shift pallet truck with charging overnight and top-ups during breaks is the natural home for a 24V 200Ah pack; a truck that lifts heavy loads all shift, runs two shifts with no charging window, or already strains its 24 V system is telling you to price the 48 V option instead. Either way, the right next step is the same: send the truck model, the shift pattern and the lift and drive peaks, and we will confirm the fit, the pack configuration and the documents for your order. We coordinate OEM/ODM battery supply from Shenzhen; we are not a factory, and every order is confirmed in writing before production begins.

Ask about a 24V forklift battery for your truck · WhatsApp +86 159 8945 0735
