Battery swap packs for boda and bajaji networks in Tanzania

In Dar es Salaam, Arusha, Mwanza and nearby towns, boda and bajaji fleets are moving toward pack swap so riders do not wait on a charger. Anyone searching for a battery swap pack for boda or bajaji networks in Tanzania needs more than a 60V or 72V label (60V and 72V supply confirmed per project). A pack that is to move between vehicles and cabinets must match series count, charge cut-off, connector, mechanical size and the BMS-to-cabinet protocol. This page is about interchangeable swap packs, not a single-vehicle conversion pack that never leaves its own charger.

LJY Energy is a LiFePO4 supplier and OEM/ODM coordinator in Shenzhen, not a factory. We do not supply cabinets, vehicles or chargers. We coordinate 51.2V 16S packs as the 48V-class reference. Any 60V or 72V pack is confirmed per project: the table below separates nominal voltage, charge cut-off, series count and BMS, because a voltage name is not a swap specification. Protocol and pin-out between the pack BMS and the cabinet are confirmed in writing for that network, not inferred from a similar model name.

Motorcycle traffic in Dar es Salaam, of the kind that boda fleets use in the city
Photo: Rasheedhrasheed, Wikimedia Commons, CC BY-SA 4.0 (resized, WebP). Illustration, not an LJY product.

Request a swap-pack checklist for a Tanzanian network · WhatsApp +86 159 8945 0735

What the operator defines per pack family

PointWhy it mattersConfirmed per project
48V-class / 51.2V 16Scommon reference for many bajaji and e-motorcycle conversionsAh, connector and cabinet protocol
60V or 72V classonly if the vehicle and cabinet actually use that windowconfirmed per project; see the series table
Charge cut-offmust match the cabinet charger, not a name on the packvolts at the connector
Connector and sizethe pack must seat in more than one cabinet and vehicledrawings and a first-article fit
BMS-to-cabinet protocolthe cabinet must see the pack dataprotocol and pin-out in writing

A voltage name is not a swap specification. 60V and 72V packs are confirmed per project after nominal voltage, charge cut-off, series count and BMS are written down and checked against the charger and the controller.

Nominal voltage, charge cut-off, series count and BMS

A 48V, 60V or 72V nameplate (60V and 72V supply confirmed per project) does not say how many cells are in series or where a cabinet charger must stop. The table multiplies public per-cell values by the series count: LiFePO4 from the EVE LF304 datasheet, NMC from the Samsung SDI 18650-25R datasheet, and lead-acid from Battery University charge limits. Every 60V or 72V pack is confirmed per project.

Chemistry and seriesNominalCharge cut-offBMS configuration
LiFePO4 16S (3.2V / 3.65V per cell)51.2V58.4V16S board
LiFePO4 20S64.0V73.0V20S board
LiFePO4 24S76.8V87.6V24S board
NMC 16S (3.6V / 4.2V per cell)57.6V67.2V16S board, NMC limits
NMC 20S72.0V84.0V20S board, NMC limits
Lead-acid 60V (5 × 12V, 30 cells, 2.30–2.45V per cell)60V69.0–73.5Vno BMS; LiFePO4 replacement confirmed per project
Lead-acid 72V (6 × 12V, 36 cells)72V82.8–88.2Vno BMS; LiFePO4 replacement confirmed per project

A 60V lead-acid set charges up to about 73.5V, while a 20S LiFePO4 pack stops at 73.0V, so 60V supply is confirmed per project and each station charger is set to the pack, not the name. A 16S BMS cannot protect a 20S pack. We never infer compatibility from a voltage name.

What the operator sends before a proposal

  • Vehicle nominal voltage and the charger’s cut-off voltage.
  • Series count and chemistry the network has already standardised, if any.
  • Connector type and the mechanical envelope of the pack.
  • The cabinet’s communication protocol, if the maker has published it.
  • How many stations and vehicles should share the same pack family.

Prove one pack family at two cabinets

Networks that seat a first pack family in two cabinets and on two vehicles, and record the cut-off and the protocol, then freeze that family, avoid a silent mismatch after dozens of packs are already in the field. Prices and lead times only in a quotation.

Boda motorcycles waiting in Bagamoyo, a coastal town on a corridor out of Dar es Salaam
Photo: Sarvesh Lutchmun, Wikimedia Commons, CC BY-SA 4.0 (resized, WebP). Illustration, not an LJY product.

How we proceed

Voltage window, series, connector and protocol → checklist and pack proposal → first-article swap → roll-out. Prices, quantities and lead times only in the formal quote.

Send the vehicle and cabinet data and request a proposal

LJY Energy, Jack Lai. Unit 705, Building 1, Lecai Industrial Park, 10 Kaijing Road, Longtian Street, Pingshan District, Shenzhen 518122, China. +86 159 8945 0735.