Floor Scrubber Battery — 24V / 36V LiFePO4 Lead-Acid Replacement

Product Overview

If you are searching for a floor scrubber battery, you are probably standing in front of a machine whose lead-acid pack no longer lasts a full shift — or you maintain a fleet of scrubbers and sweepers and are tired of watering batteries, cleaning corroded terminals and rotating machines out of service while packs charge. This page covers the LiFePO4 (lithium iron phosphate) replacement packs we configure for walk-behind and ride-on floor cleaning machines, and — just as important — how to confirm a pack actually fits your machine before you order.

Most floor machines run on one of three voltage platforms. Walk-behind scrubbers are predominantly 24V, typically in the 60–180Ah range, and many were designed around standard GC2-size lead-acid batteries, which makes a same-footprint lithium drop-in the simplest swap. Ride-on scrubbers and larger sweepers commonly run 36V, and some heavy machines use 48V. We configure packs across all three platforms. LJY Energy is a China-based LiFePO4 battery supplier and OEM/ODM coordination partner: we match cell configuration, BMS and enclosure to your machine and confirm the final specification with you in writing before production.

Why Buyers Replace Lead-Acid in Floor Machines

The lead-acid pack a scrubber ships with is usually the first component to age out. Flooded batteries need regular water top-ups, and in a cleaning contractor’s depot that maintenance either gets done — at labour cost — or gets skipped, and the pack dies early. Charging discipline is the second problem: lead-acid wants a full, uninterrupted charge and suffers when operators plug in for a partial top-up between shifts, which is exactly how cleaning equipment is actually used.

LiFePO4 changes the working pattern rather than just the chemistry:

  • Opportunity charging is normal use. Partial charges between shifts do not damage the pack the way they shorten lead-acid life. A machine can top up during a lunch break instead of sitting out a full charge cycle.
  • No watering, no acid, no terminal corrosion. Sealed lithium packs remove the weekly maintenance round and the acid damage to trays and connectors that comes with it.
  • Usable capacity is larger in practice. A lead-acid pack is normally kept above roughly 50% discharge to protect its life; a LiFePO4 pack is routinely worked to 80% depth of discharge, so a smaller nameplate capacity can cover the same shift.
  • Voltage stays flat through the shift. Brush and vacuum motors keep their performance instead of fading as the pack drains.
  • Weight drops substantially. That makes packs easier to handle at swap time — but check the fitment notes below, because on some machines the battery’s weight is part of the design.

Cycle life is the other half of the economics. A typical reference for quality LiFePO4 cells is around 6,000 cycles at 80% depth of discharge at cell level; pack-level results depend on the BMS, the enclosure and how the machine is worked. Against a lead-acid pack replaced every couple of years in daily service, the lithium pack’s higher purchase price is spread over a much longer service life — send us your machine count and shift pattern and we will help you run that comparison for your fleet.

Typical Configurations

Values below are typical configurations for this application. Items marked “To be confirmed” depend on your machine model and the final build, and are confirmed per project in the written quotation.

Group Parameter Value Status
Electrical Battery chemistry LiFePO4 (lithium iron phosphate) Typical
Electrical Nominal voltage 25.6V (24V platform) / 38.4V (36V platform) / 51.2V (48V platform) Typical
Electrical Rated capacity 24V: 60–180Ah range; 36V and 48V sized per machine Typical range — exact build to be confirmed
Electrical Enclosure format GC2-footprint drop-in and machine-specific tray sizes To be confirmed per machine model
BMS Protection Over-charge / over-discharge / over-current / short-circuit / temperature protection Typical
BMS Continuous discharge rating Matched to machine motor and brush load To be confirmed per project
Charging Charge profile LiFePO4 CC/CV profile; 24V platform absorption 28.4–29.2V Typical
Charging Onboard charger compatibility Lithium-profile charger, or existing charger settings verified before order To be confirmed per project
Physical Dimensions & weight Per final enclosure design — datasheet on request To be confirmed
Physical Ingress protection Sealed enclosure; rating per final configuration To be confirmed per order
Compliance Transport & safety documents UN38.3 test summary and SDS available per model To be confirmed per model
Commercial Warranty terms Subject to configuration and order agreement To be confirmed

Fitment Confirmation Checklist

A lithium pack is only a good replacement if it fits the machine mechanically, electrically and in daily operation. Buyers most often ask us about fitment for Tennant, Nilfisk, Kärcher, Hako and Viper machines. Treat those brands as the starting point of a confirmation process, not as a compatibility certificate: we do not claim certified compatibility with any machine brand. Before any order, we confirm the following with you in writing, against your exact machine model:

  1. Machine brand, model and year — tray dimensions and connector types change between generations of the same model line.
  2. Original battery specification — voltage, capacity, and whether the machine runs one pack or several batteries wired in series/parallel.
  3. Battery compartment dimensions and terminal position — length × width × height of the tray, terminal type and cable reach. A photograph of the compartment with a tape measure in frame settles most questions.
  4. Charger check — does your existing charger offer a lithium (LiFePO4) profile? If it is a lead-acid-only charger with an equalisation stage, it is not suitable as-is; the charge curve must be confirmed or the charger replaced as part of the conversion.
  5. Duty pattern — shifts per day, opportunity charging or overnight only, and whether the machine works wet areas where a sealed enclosure matters.
  6. Weight and balance — some scrubbers rely on battery mass for traction or pad pressure. If your machine is one of them, tell us: the lighter lithium pack may need ballast, and that is far easier to plan before shipment than after.

Send items 1–4 with your inquiry and we can normally confirm a build without a long exchange of emails.

Wholesale, OEM & ODM

We supply cleaning-equipment distributors, rental fleet operators, facility-service contractors and machine refurbishers.

  • Wholesale: replacement packs configured per machine model for resale or fleet conversion programmes; terms vary by configuration and order size.
  • OEM branding: your label, packaging and documentation on standard configurations.
  • ODM configuration: voltage, capacity, enclosure footprint, connector and BMS options matched to a machine family you service.
  • Samples: a single machine conversion is the normal way to evaluate before committing a fleet.

Frequently Asked Questions

Will a LiFePO4 pack fit my Tennant or Nilfisk scrubber?

Quite possibly — both brands build many machines around standard battery footprints — but “same voltage” is not the same as “fits”. Tray size, terminal layout and the charger decide it. Send us the machine model and the dimensions of the battery compartment, and we will confirm the exact build in writing before you order. We do not publish a blanket compatibility claim for any machine brand.

Can I keep my existing charger?

Only if it can be set to a lithium profile: correct absorption voltage for the platform and no equalisation stage. Many chargers fitted for flooded or AGM batteries cannot, and using one anyway risks overcharging the pack. Checking the charger model is a fixed step in our fitment confirmation, and if a replacement charger is needed we will say so in the quotation rather than after delivery.

How long will it run per shift?

Runtime is usable capacity divided by the machine’s working draw. Because a LiFePO4 pack can be worked to about 80% depth of discharge (against roughly 50% for lead-acid in service), a lithium pack of the same nameplate capacity typically covers noticeably more cleaning time — and it holds voltage, so the machine feels the same in the last hour as in the first. Give us your machine model and current battery size and we will size the pack against your shift length.

My machine uses GC2 batteries. Is there a drop-in option?

Yes — GC2-footprint lithium packs exist precisely for machines built around pairs or quads of GC2 lead-acid batteries, and they remove the series-pair balancing problem along with the watering. The charger check still applies, and on some machines the weight difference needs a ballast decision. Both are covered in the fitment checklist above.

Can operators charge the machine between shifts?

Yes — that is one of the main reasons fleets convert. LiFePO4 accepts partial charging without the life penalty lead-acid suffers, so a top-up during breaks is normal operation, not abuse. For a fleet working multiple shifts, this often matters more than the headline capacity.

What do you need from me for a quotation?

Machine brand and model, the current battery’s voltage and capacity, a photo of the battery compartment if you can manage it, the charger model, and roughly how many machines you are converting. With that, we confirm configuration, documents and price in a written quotation — specifications, certifications and delivery terms are confirmed per project, not published as blanket claims.

Request a Quotation

Converting one machine or a whole fleet, start with the fitment details above: request a floor scrubber battery quotation and include your machine brand, model and current battery size. We will confirm the configuration and charger compatibility in writing before anything is produced.

Specifications are typical configurations and subject to the final order specification. Fitment, certifications, warranty and pricing are confirmed per inquiry.